Has an identifier field of X’00’ and a modifier field of X’00’.
NJTGFLG1 - Reserved
NJTGXCLS - Execution class
NJTGSTRT - Start time
NJTGSTOP - Stop time
NJTGALIN - Total lines
NJTGACRD - Total cards
NJTGIXPR - Requested execution priority
NJTGAXPR - Actual execution priority
NJTGIOPR - Initial job priority
NJTGAOPR - Actual output selection priority
Reserved.
Length and type: 1 bit
Default value: 0
Actual job execution class.
AS/400 and JES3 do not use this field and set it to zero.
RSCS and POWER do not use this field.
Length, type, and range: 1 character (A-Z, 0-9)
Default value: A
Time of day the job started execution in System/390 TOD clock format (local time).
JES2 uses this field in SMF type 26 records and sets the time of day.
AS/400, JES3, RSCS, and POWER do not use this field and set it to zero.
Length and type: 8 binary
Default value: 0
Time the job completed execution in System/390 TOD clock format (local time).
JES2 sets the field to zero or the default value for spin data sets.
AS/400, JES3, and RSCS do not use this field and set it to zero.
POWER does not use the field but sets it. For spin output, all trailers except the last one are zero.
Length and type: 8 binary
Default value: 0
Total number of print lines for this job or job segment at all locations. Not multiplied by the number of copies.
AS/400 does not use this field but sets it to the number of records if it is a print file.
JES2 sets the field to zero or the default value if SYSOUT gets sent before the job finishes executing.
RSCS does not use this field but sets it to the umber of records in the file (from TAGRECNM) if the file is a print file.
POWER sets the field to the number of records produced by the job. For jobs that contain a spin-off data set, all trailers except the last one are zero.
Length and type: 4 binary
Default value: 0
Total number of card images produced for this job or job segment at all locations. Not multiplied by the number of copies.
AS/400 does not use this field but sets it to the number of records if it is a punch file or SYSIN.
JES2 sets the field to X'00' for jobs that contain spin-off data sets.
RSCS does not use this field but sets it to the number of records in the field (from TAGRECNM) if it is a punch file (SYSOUT) or SYSIN.
POWER does not use this field but sets it to the number of records produced by the total job. For spin output, all trailers except the last one are zero.
Length and type: 4 binary
Default value: 0
Initial requested execution selection priority.
AS/400 does not use this field but sets it to the AS/400 transmission priority shown in NJHGPRIO.
JES2 does not set this field but uses it. The SYSOUT receiver shifts the low-order 4 bits to the high-order four bits of JCTIPRIO.
JES3 does not use this field but sets it to the default value.
RSCS does not use this field but sets it to the RSCS transmission priority shown in NJHGPRIO.
POWER sets this field from the PRI= parameter on the * $$ JOB statement.
Length, type, and range: 1 binary (0-15)
Default value: 0
Actual execution selection priority used.
AS/400 does not use this field but sets it to the AS/400 transmission priority shown in NJHGPRIO.
JES2 does not use this field but sets it.
JES3 does not use this field but sets it to the default value.
RSCS does not use this field but sets it to the RSCS transmission priority shown in NJHGPRIO.
POWER does not use this field but sets it to the default value.
Length, type, and range: 1 binary (0-15)
Default value: 0
Initial job priority for output selection.
AS/400 does not use this field but sets it to the AS/400 transmission priority shown in NJHGPRIO.
JES2 does not use this field but sets the range (0-15) when the SYSOUT job gets selected for transmission. (JES2 sets the field to 1 for spin data sets if the job is still executing.)
JES3 uses the greater value of NJTGIOPR or NJTGAOPR for the job's priority for received output (unless greater than 14, in which case 15 is used). This field is set from the job's priority for outgoing SYSOUT.
RSCS does not use this field. It is et to the RSCS transmission priority as shown in NJHGPRIO.
POWER sets a default value but does not use it.
Length, type, and range: 1 binary (0-255)
Default value: 0
Actual output selection priority used.
AS/400 does not use this field but sets it to the AS/400 transmission priority shown in NJHGPRIO.
JES2 does not use this field but sets it to the default value.
JES3 uses the value of NJTGIOPR or NJTGAOPR (whichever is larger) for the job priority for received output. If the value is greater than 15, uses 15. Field gets set from the job's priority for outgoing SYSOUT.
RSCS does not use this field. Set to the RSCS transmission priority shown in NJHGPRIO.
POWER does not use the field but sets it to the default value.
Length, type, and range: 1 binary (0-255)
Default value: 0