Getting started with ADEPT Suite

Follow the steps below to install and configure TOOLS for the first time. The steps below assume that you have already installed the Barr Host Communications Suite. Once these steps are complete, you can start using the features of TOOLS, such as viewing or printing selective page ranges of Xerox jobs.

You can use the optional TRANSFORM to convert the data to PCL, PostScript, or PDF for printing, archiving, or viewing on the Internet.

See also:


Installing the transformation software

The setup program copies files from the ADEPT Suite CD to your computer.

  1. Before you run the setup program, exit all Windows programs and make sure the hardware key is installed.

  2. Insert the ADEPT Suite CD into the CD-ROM drive. The installation screen automatically displays. If auto run is disabled on your system or if the installation screen does not automatically display, right-click Start on the taskbar and select Explore. Navigate to the CD-ROM drive and double-click setup.exe.

  3. Follow the instructions on the screen to install the software.

Top

Configuring the software

The Transform Configuration utility is used to configure the initial settings and the default values for interpreting jobs. Use the utility after the transform software has been installed, but before copying the resources to your computer.

  1. Open Windows Explorer.

  2. Navigate to the folder where the Barr software is installed.

  3. Double-click TransformationConfiguration.exe. The Transformation Configuration dialog box displays.

    Transform Configuration dialog box

  4. Review the settings under Folders. In most cases, the default settings will apply.

  5. Do not modify the Conversion option. The option only applies to the TRANSFORM module.

  1. Under Spool fields, specify which spool header fields (or document attribute fields) will be used to set different settings on a job-specific basis. The INI spool field parameter indicates that the specified spool header field (Form name by default) can be used to select an INI file other than the DEFAULT.INI. When the Barr software interprets a job, it will first look for an INI file that matches the name in this field. If it does not find an INI file with that name, it will use the DEFAULT.INI file. The Output parameter applies only to the TRANSFORM module.

  2. Click OK. The utility will create a DEFAULT.INI file used to specify the settings. The INI file, along with the resources, will be stored in the C:\Transforms folder, unless an alternate location was specified during configuration.

Top

Copying the Xerox resources to your computer

Any product that interprets or transforms Xerox legacy data streams (LCDS or Metacode) must use the same resources as the Xerox LPS printer. These resource files, which are typically stored on the Xerox printer, must be copied to the C:\Transforms\Res folder for use by the Barr software when interpreting Xerox jobs. The following resources are needed:

It is simple to copy the resources from the Xerox printer to disks using system commands from the Ready prompt on the Xerox controller. If the disks are not formatted for the Xerox operating system, use the FLOPPY INITIALIZE command to correctly format the disks. To copy the resources to a disk, use the following commands:

FLOPPY SAVE *.JSL

FLOPPY SAVE *.FRM

FLOPPY SAVE *.FNT

FLOPPY SAVE *.LGO

FLOPPY SAVE *.IMG

When one disk is full, the system will prompt you to insert another disk.

Top

Copying the PCL resources to your computer

A standard collection of PCL fonts is provided with the Adept Suite.

Additional specialized fonts can be added to the standard folder, or the folder path can be reconfigured by the following INI entry:

[PCL]

PCLFontLibDir=C:\Program Files\BARR ADEPT Suite\PCL_Fonts\

Top

Normalizing the jobs

The normalizing utility reformats the jobs into page-oriented data with basic page indexing. This reformatting enables all the other features, such as printing selective page ranges, splitting the job, or gathering accurate accounting information.

Normalizing can occur manually or automatically. You can manually normalize the job by right-clicking the job in the Spool Window and selecting Tools | Normalize. Manually normalizing jobs works best when you occasionally need to reprint jobs, but in most cases, you want the Barr software to send the data to the printers.

If you intend to use accounting information or want to use BARR/PRINT SPLITTER, then you need to automate the normalizing process. You can configure each input type in the Barr Host Communications Suite to normalize jobs as they arrive in the Spool Window.

Normalizing Data

Data can be configured to normalize automatically on input to the Spool Window

Normalizing can be enabled for specific input data streams by setting a single option for the specific input type. The following table shows where to set the normalizing option for each type of input.

Input Type

Set Normalizing Option

RJE or NJE

By override tables

LPD

By queue

Socket

By socket

Print Utility (input from disk)

By folder

Once you have determined which input you are using, modify the settings for that input to add a new document attribute from the Data Set Header Internal Custom section. The attribute is NDHBNORM – Normalize the data set, and its value should be set to -1.

Top

Viewing or printing jobs

The viewing utility allows you to preview selected pages of the input data stream. By viewing the data before you print, you can verify that the job configuration settings are correct.

Use one of the following methods to view the data WYSIWYG.

To view the data with the standard Barr text/binary Viewer utility, right-click the document and select View | Text.

To print the document, set the document and printer routing criteria to match, and change their states to Ready.

You can also configure a reprint range using the Viewer's Restrict Output Page Range options.

Top